It is a texture of chesterfields. The skin is highly worn with a lot of scratches, cracks and cuts. Some damaged areas even expose the yellow sponge-like filling of the sofa.

With the SBSAR file, the amount of cushions, the bulge level of cushions, the number of cuts and colors etc. can be changed.

They are old wood planks which have a lot of wear, cracks and scratches. Wood grains can also be seen.

The plank amount, grout width, wood color etc. can be changed by the SBSAR file.

It is a worn brick wall. Some bricks have been badly damaged and exposed inner part of the bricks which have different colours than outer paint. The bricks were roughly glued together. Thus, a lot of cement exists out of the grout.

The SBSAR gives users the flexibility to set the brick amount, colours and fine tune the damage level.

It is an old worn concrete wall which has a lot of large holes exposing inner reinforcement bars (rebars). The outer paint is also peeling off. Numerous cracks also appear on the concrete.

Using the SBSAR file, the wall colour, number of concrete plates and rebars, depth of holes etc. can be set.

They are old and worn roof tiles. Since the tiles are on the rooftop, it is full of lichen and bird poop.

With the SBSAR file, the amount of tiles, lichen, bird poop, dirty level, damage level can be manipulated.

The base is an asphalt road which is covered with bitumen of various colours.

Due to weathering, cracks can be found on the surface. The SBSAR file allows the amount and depth of the cracks to be adjusted.

It is the base concrete texture. It is primitive and raw having large and small pores on the surface.

It is suitable for building plain walls, especially those in industrial style. The SBSAR file allows the hole sizes and depths to be adjusted.

It is a cactus. The texture maps contain a combined version of the cactus body and its spines, and separated layers of the body and spines.

The combined version let you texture a cactus quickly while the separated version let you adjust the spines and make them more pop put.

With the sbsar file, you can adjust the damage level of the cactus, number of columns of spines etc.

They are brown rocks covered by fresh snow. Some snow has melted leaving damp mark on the snowy ground.

With the sbsar file, rock size, snow level and fresh and melted snow amount can be controlled.

It is a red sandstone or mudstone texture. Sandstone is a sedimentary rock composed mainly of tiny silicate grains.

This rock can increase the varieties of stone species in the natural environment of CG scene.

It is a wall made of concrete plates, but it is highly eroded making a very bumpy surface.

With the sbsar file, the grout intensity and damage level can be adjusted.

It is a brick wall texture which can be used for texturing medieval forts. Of course, it is suitable for modern architecture. There are smaller pebbles between large bricks.

It is a floor covered with irregular stones and a thin layer of sand is covering the rocks. It is a good material for both modern street view or medieval scenes.

It is a simply rock texture, but can be applied to a large varieties of natural environment. It is simple, but useful.

It can be used to texture a single stone or as a rocky ground of cliff.

It is a spider web. Some people may call it cobweb. Technically they are different, but most people use these 2 terms interchangeably.

With the sbsar file, you can control the damage level and number of silk lines. Besides, the deformation can also be controlled.

It is a concrete wall with some plaster, but has numerous dents of various sizes due to bumps, hits or shots.

It is a rocky and sandy ground where a lot of fossils were found. Among the fossils, some are popping up after the mud has been cleaned. They are waiting to be removed. Whereas the removed fossils left fossil holes on the muddy ground.

They are wood planks with nails on both ends. Rust can be found on the nails. The wood planks has a lot of worn areas due to weathering. Knots also appear on the planks.

They are wood planks painted in red, but some paint is peeling off due to weathering. Besides, there are wear and broken parts.

It is a fabulous material for creating old doors, fences and even houses.

It is a concrete texture composed of Corinthian columns. Due to weathering and aging, a lot of wear and cracks appear on the surface.

Despite its name columns, this texture suits extremely well for walls and urns.